414 guides across 21 subjects
Every figure traced to a named source
Prices in Ugandan shillings, per acre and per animal

Tractor Horsepower Explained

A tractor fitted with a front loader

Tractor horsepower measures the rate at which a tractor does work, and the same machine carries at least three different horsepower figures: one at the engine, one at the power take off shaft and one at the drawbar. Tractor horsepower explained properly begins there, because those numbers are not interchangeable. How much you need is set by implement width, working depth and soil texture.

What Horsepower Measures on a Farm Tractor

Horsepower is force multiplied by distance, divided by time. James Watt fixed the unit while rating steam engines against the animal they were replacing, and the figure he settled on, 550 foot pounds of work per second, was already more than a real horse could sustain. That is the whole definition, and two useful things follow from it.

The first is that power combines pull and speed. A tractor dragging 10 kilonewtons at two kilometres an hour and a tractor dragging 5 kilonewtons at four kilometres an hour are producing the same power. Which of them you want depends on the implement, because a plough in heavy soil needs the pull, while a harrow or a sprayer needs the speed.

The second is that power is only delivered when the load moves. A tractor straining against a plough that has stopped dead is producing no useful power at all, whatever the engine is doing. Force on its own is draft, measured in pounds or kilonewtons, and on a Ugandan farm draft is the number that actually decides whether a job can be done. Power tells you how fast.

Engine Power, PTO Power and Drawbar Power on a Farm Tractor

Power leaves the engine and loses something at every stage on its way to the soil. Three measuring points matter and each gives a smaller number than the one before it.

The three places a tractor's power is measured, and what each one is good for.
Engine or gross power. Measured at the crankshaft, with the engine on a test bench rather than in a field. It is the largest number and the one most likely to appear in an advertisement. Nothing on the farm ever receives it, because the fan, the alternator, the hydraulic pump and the transmission all take a share before it leaves the machine.
Power take off power. Measured at the splined shaft at the back of the tractor, so it is what a driven implement such as a thresher, a sheller, a rotary tiller, a mower or a pump actually gets. Use this figure for anything the tractor drives rather than pulls.
Drawbar power. Measured as pull at the hitch multiplied by forward speed, so it is what a plough, harrow, ridger or trailer actually gets. It is the smallest of the three, because on top of the transmission losses the tractor has to push itself along and its tyres slip. Use this figure for anything the tractor pulls.

How large the drop is between those three points varies with the machine, the tyres, the ballast and the ground, which is why no honest single percentage can be quoted for it. What is reliable is the direction and the order. If a specification sheet gives you one number without saying where it was measured, you have been told very little, and if the figure quoted is the engine number you will be short of power at the plough by a margin nobody has told you.

How Tractor Power Is Tested Before It Reaches a Farm

There is a standard behind these numbers, and knowing it is what lets you compare two machines honestly. Tractors are tested under the codes of the Organisation for Economic Co-operation and Development. Twenty nine countries adhere to the OECD tractor test codes, with active test stations in roughly 25 of them, and reciprocity means that once a test report is approved every participating country must accept it. Tractors are tested in the country of manufacture. The University of Nebraska Tractor Test Laboratory, the officially designated station for the United States, has tested 2,053 tractors since 1920.

Two details of how the testing is done matter to a farmer in Uganda.

Power take off performance is measured on a dynamometer at a controlled temperature under the OECD performance code, which is a clean, repeatable measurement. The drawbar test is different: it is run on a concrete or asphalt track, in gears up to about 10 miles an hour, with wheel slip held below 15 percent. Concrete is used so that every tractor in every country is tested on the same surface, because on soil the results would depend on whose soil it was.

The consequence is unavoidable and it is the single most useful thing on this page. A tested drawbar figure is a best case, recorded on the best traction surface a tractor will ever meet. Your field will give less, and a wet clay field in the middle of a Ugandan rainy season will give a great deal less. Never plan an implement width off a drawbar figure without leaving room for that.

Why Implement Width and Soil Type Set the Power You Need

Buyers usually work forwards: pick a horsepower, then see what it will pull. Machinery engineering works backwards, and so should you. The implement has a draft requirement, the draft requirement depends on how wide it is, how deep it runs and what the soil is made of, and the power follows from those.

Draft is the force needed to move an implement forward, and for tillage tools it is almost entirely resistance from soil and crop residue. Engineers sort soils into three groups for this purpose, which is coarser than a soil map and far more useful: coarse means sandy, medium means loamy, and fine means high in silt and clay. Draft rises as you move from coarse to fine. It also rises with working depth, and it rises in dry consolidated ground compared with the same soil when moist and friable.

The figures below come from the American Society of Agricultural Engineers machinery management data, as reproduced in a technical guide to implement draft. They are published in pounds of pull per foot of implement width, at tools working at about two miles an hour; the conversion into kilonewtons per metre of width is arithmetic on those published values.

Tillage tool Coarse soil Medium soil Fine soil
Plough at 15 cm 4.7 7.2 10.8
Plough at 20 cm 6.1 9.5 14.4
Tandem disc 2.0 2.3 2.6
Single disc gang 0.8 0.9 1.1
Spring tine at 5 cm 1.3 1.7 2.0
Spring tine at 8 cm 1.9 2.5 2.8

Read the top two rows and the whole argument of this page is in front of you. The same plough, at the same depth and the same speed, needs about 2.3 times the pull in clay that it needs in sand. Take the same plough from 15 centimetres down to 20 in clay and the pull rises by roughly a third again. Nothing about the tractor changed in either case. Soil and depth did.

Notice too how much lighter the disc and tine figures are. A tandem disc harrow in fine soil asks about a quarter of what a plough asks in the same field. That is why a tractor which cannot plough your heaviest ground may still harrow it perfectly well, and why the honest question is never "how many horsepower" but "how many horsepower for which operation in which field".

Working Out Drawbar Power From Plough Draft and Soil Type

Take a plough cutting one metre of width at 15 centimetres deep, pulled at five kilometres an hour, which is 1.39 metres a second.

Drawbar power for a one metre plough at 15 cm, worked from the draft figures above.
Sandy soil. 4.7 kilonewtons of pull multiplied by 1.39 metres a second gives about 6.5 kilowatts, near 8.8 horsepower, delivered at the drawbar.
Loamy soil. 7.2 kilonewtons gives about 10 kilowatts, near 13.4 horsepower.
Clay soil. 10.8 kilonewtons gives about 15 kilowatts, near 20.1 horsepower.
Clay soil at 20 cm. 14.4 kilonewtons gives about 20 kilowatts, near 26.8 horsepower.
Then add the losses. Those are drawbar figures, so the engine has to supply them plus transmission losses, plus rolling resistance, plus whatever is wasted in wheel slip, plus anything the ground slopes. The published draft values are also measured at about two miles an hour and draft climbs with speed, so at five kilometres an hour they are a floor rather than a ceiling.

The arithmetic is worth doing yourself with your own numbers, because it turns a guess into a calculation. Measure the working width of the implement you intend to use, decide the depth you actually need, be honest about which of the three soil groups your worst field belongs to, and work up from there. What you will usually find is that the plough sets the requirement and everything else on the farm fits inside it, which is exactly why choosing a tractor treats the implement decision as the one that comes first.

Wheel Slip and Ballast: Why Engine Power Alone Will Not Pull a Plough Through Soil

A tractor converts engine power into pull through the contact between its tyres and the ground, and that conversion is where most of the loss in the field happens. Pull is limited by grip, not by the engine, which is why a machine can have power in reserve and still sit spinning.

Three things set the grip. Weight on the driven wheels, because pull comes from the load pressing the tyre into the soil. Tyre condition and inflation, because a worn or over inflated rear tyre puts less tread into contact. And the soil surface itself, which is why the OECD drawbar test uses concrete and why your field will never match it.

Slip is the measure of the loss. Some slip is normal and necessary, and the OECD test caps it at 15 percent, which tells you what a well matched tractor and load look like. Too little slip usually means the tractor is heavier than the job needs, and every extra kilogramme is fuel burned carrying itself around. Too much slip means the wheels are turning without the tractor advancing, so fuel is being converted into tyre wear and a smeared furrow bottom instead of work.

Ballast is the adjustment. Wheel weights, front weights or a mounted implement shift load onto the driven wheels, and water in the rear tyres does the same thing more cheaply. It is an adjustment in both directions: adding ballast to cure slip in heavy ploughing, and taking it off for light work so the machine is not compacting ground for nothing. A tractor set up once and never changed is wrong most of the year.

What Happens When a Tractor Is Underpowered for Heavy Soil

An underpowered tractor does not simply work more slowly. It works differently, and most of the differences cost money.

First it slips. The wheels spin, forward speed collapses and the engine note drops, and on wet clay a spinning wheel polishes and seals the furrow bottom, which is one of the ways a plough pan starts. Then the operator compensates, and the compensations are the real damage. The plough comes up to a shallower depth than the crop needs, because draft falls sharply when depth falls. Or a furrow is taken off the plough to reduce width, which is the correct response but leaves more passes to make. Or the clutch is slipped and the gearbox laboured to get through a hard patch, which is how transmissions die. Fuel per acre climbs, smaller machine or not, because the work is being done badly.

The quiet cost is timing. A machine that cannot keep up stretches land preparation across days the season does not have, and in rainfed tropical conditions the window for tillage rarely runs past 30 days. Work in this region puts the yield penalty at up to 100 kilogrammes per hectare for every day planting slips past the right date, which is a larger number than most fuel savings.

The right response is usually the implement, not the tractor. Narrow the cut, take a furrow off, work shallower where the crop allows it, or move to a tool with a lower draft such as a tine or disc implement. The draft figures above show how much that buys you.

What Happens When an Overpowered Tractor Works a Small Farm

Oversizing is the commoner mistake in places where a tractor is a status purchase, and it has its own bill.

Fuel comes first. A diesel engine is at its most efficient when it is reasonably well loaded, and a large tractor pulling a small implement runs lightly loaded all day, burning more fuel per acre than a smaller machine doing the same work properly. The engine is not working harder, it is idling expensively.

Weight comes second, and on a smallholding it is the more lasting cost. Every pass presses the soil, the pressure carries down below the depth the plough reaches, and repeated traffic builds a compacted layer that water cannot enter and roots cannot cross. A heavier machine makes that layer sooner. Pair it with the habit of ploughing to the same depth season after season and you get a hardpan, which then needs a subsoiler run below it to break, at a pull that is heavier than the ploughing ever was. The two wheel tractor page covers how to test for a hardpan and how deep to go, and soil testing is worth pairing with a spade check.

Then there is the geometry. UBOS finds half of Ugandan agricultural households working at most two gardens and a third working three or four, and on a small irregular plot a long tractor with a wide implement spends much of its time on headlands and turns. Add the cost of getting a heavier machine down a farm track, across a culvert and through a gateway, and the capacity you paid for is unreachable.

Finally the repair bill scales with the machine. Bigger tyres, bigger filters, bigger hydraulic components, and a smaller chance that anyone within reach stocks the parts.

Reading a Tractor Specification Without Being Misled on Farm Power

Specification sheets are written to sell, so read them with a few questions in hand.

What to ask about any horsepower figure you are shown.
Measured where? Engine, power take off, or drawbar. If the sheet does not say, assume the largest and most flattering of the three.
Measured by whom? An OECD test report is a third party measurement that every participating country must accept. A manufacturer's own brochure figure is not the same thing.
At what engine speed? Maximum power and power at rated speed are different numbers, and the one a tractor can hold all day is the rated one.
On what surface? Any drawbar figure worth quoting was recorded on concrete. Your field is not concrete.
With what fitted? Ask whether the figure was taken with the tractor ballasted and with front drive engaged, because both change the drawbar result.
And the question the sheet cannot answer. Whether anyone within a day's travel stocks parts for it. Choosing a tractor deals with that, and it outranks every number above.

Horsepower on a Two Wheel Tractor and on an Ox Team

Horsepower is not a four wheel tractor idea alone, and setting the small power sources beside the large ones puts the numbers in proportion.

A two wheel tractor, the walking machine also sold as a power tiller, sits at 8 to 20 horsepower. Go back to the worked sum above and that range covers a one metre plough at 15 centimetres in sandy or loamy soil with something to spare, and runs out in clay at depth, which is precisely the pattern reported from the field: these machines work well on flat, light, stone free ground and are not recommended in wet heavy soil. The same engine also drives a pump, a thresher or a sheller, where the job is steady rotation rather than pull, and that is where its power goes furthest.

An ox team is a power source too, and the way its limit is expressed is instructive. A well conditioned pair sustains a pull of 10 to 12 percent of its body weight through a working day, with more for short bursts. That is a draft rating, not a power rating, and it is the honest way to describe any tillage power source, because the pull is what decides whether the plough moves. Speed then decides how long the field takes.

Which is where this page ends up. Horsepower is a useful number for comparing machines and a poor number for choosing one. Draft, depth and soil choose the machine, and horsepower tells you how quickly it will get through the work.

Questions Ugandan Farmers Ask About Tractor Horsepower

Is engine horsepower or PTO horsepower the number I should compare? Compare the one that matches the job. Power take off horsepower for anything the tractor drives, such as a thresher, sheller, rotary tiller or pump. Drawbar horsepower for anything it pulls, such as a plough, harrow, ridger or trailer. Engine horsepower is the least useful of the three for a farmer, because nothing on the farm receives it.
How much horsepower do I need per acre? Acres do not set horsepower, and the rule circulating online that puts one to two horsepower on every acre produces nonsense at Ugandan holding sizes, where it would size a machine for a three acre farm at about three horsepower. Implement width, working depth and soil texture set the requirement. Acreage sets how many hours the work takes once the power is right.
Why does my tractor manage one field and stall in another? Almost always soil texture, depth or moisture. The published draft data shows the same plough at the same depth needing roughly 2.3 times the pull in a fine clay soil that it needs in a coarse sandy one, and dry consolidated ground resists more than the same soil moist. If a field has beaten you, take a furrow off or work shallower there rather than forcing it.
Will a bigger tractor plough deeper? Up to a point, and then it does something you do not want. Deeper work needs more pull, so more power helps, but weight and repeated passes at the same depth build a compacted layer under the furrow that blocks water and roots. Vary the working depth between seasons and check for a pan with a spade before assuming more power is the answer.
What does a two wheel tractor's horsepower actually let it do? At 8 to 20 horsepower it will plough light and medium soil at normal depth, drive a pump, a thresher or a sheller, and pull a trailer loaded up to about a tonne. It will not hold a wide plough at depth in wet clay, and it is not recommended in very wet soils at all. The two wheel tractor guide covers the full range.
Does horsepower change what a tractor costs to run? Yes, in both directions, and not in proportion to the rating. An undersized machine burns more fuel per acre because the work is done badly, with slip and repeated passes. An oversized one burns more fuel per acre because a lightly loaded diesel is inefficient and because the machine is carrying weight it does not need. Parts, tyres and filters also get dearer as the machine gets larger. The figures that exist for Ugandan machinery running costs are in the choosing a tractor FAQ rather than here.
Can I trust the horsepower figure a seller quotes? Trust a test report, not a sticker. Ask which of the three figures it is, at what engine speed, and whether it comes from an OECD test. If none of those questions can be answered, treat the number as marketing and judge the machine by the implement it can hold in your worst field.

Checking Horsepower Claims With Suppliers in Uganda

Before comparing quotations, write down the implement you will use, its working width, the depth you need and which soil group your hardest field belongs to, then ask each supplier what power the machine delivers at the power take off and at the drawbar, and where those figures came from. A supplier who can answer that is worth more of your attention than one quoting the biggest number. Ask the same people where parts are stocked and who services the machine in your district, because a power figure is worth nothing on a tractor that is standing still. The farm machinery guides cover the implements that set the requirement, tractor implements explained gives the working widths to plan from, and the supplier directory is where to start gathering written quotations.

More in Farm Machinery