414 guides across 21 subjects
Every figure traced to a named source
Prices in Ugandan shillings, per acre and per animal

Maize Shelling Machines

Tractors and a forage harvester working a field

Maize shelling machines strip grain off the cob mechanically, and a small four horsepower engine driven sheller gets through in one hour what one person shelling by hand manages in a full working day. Motorised shelling reaches most Ugandan farms as a hired service rather than as something a smallholder owns. What decides whether it pays you is grain moisture at shelling, because moisture sets how much grain cracks, and cracked grain is what a buyer docks you for.

What a Maize Shelling Machine Does to the Crop

A maize sheller is a simple machine doing one job with a lot of force. Dehusked cobs go into a hopper and slide onto a rotating drum inside a curved chamber. The drum carries a narrow beating ridge, and the grain comes off by abrasion as the cob is dragged past it. Grain falls through a coarse screen onto a collecting pan and out one exit. The spent cob is pushed out another. A fan mounted on the side blows chaff and dust off the kernels as they leave, so the machine shells, separates and cleans in one pass. IITA's training manual for smallholder maize farmers describes exactly this layout on the four horsepower diesel machine it recommends, and notes that one person can run it and that it can be wheeled from one homestead to the next.

That last point is the one that matters in Uganda. Almost nobody with two acres is going to own this machine. It circulates.

The machine has no intelligence in it. It applies the same force to a cob whether that cob is at 22 percent moisture or 11 percent, and the grain behaves very differently at those two figures. Which is why a page about shelling is mostly a page about moisture.

Hand Shelling and Stick Beating: the Uganda Baseline

Before comparing machines, it is worth being precise about what they replace, because the Ugandan baseline is not one method but two.

The FAO, WFP and IFAD food loss study of the Ugandan maize chain, which ran field work in Apac and Lira in the Lango subregion, recorded shelling done with knives and bare hands for small quantities and with a stick for anything larger. Hand shelling was described as laborious and not feasible for large volumes, so farmers resort to beating. Beating breaks grain. Some grain is spilled and scattered during the operation and, in the study's words, in many cases cannot be recovered. The district mean loss at shelling came out at 4 percent, sitting alongside 3 percent at drying and 10 percent in on farm storage.

The study also recorded the availability picture plainly, and it is the sentence worth carrying away: a few shellers exist in Lira, and most of the farmers interviewed had not accessed them.

So the honest starting position for a Ugandan maize grower is not choosing between a stick and a machine. It is finding out whether a machine comes anywhere near your village during the four or so months over which harvest runs, because not everyone plants at the same time and the shelling demand is smeared across that whole window.

Shelling Throughput Per Hour on a Ugandan Maize Farm

The throughput figures circulating on equipment catalogue pages, three to four tonnes an hour and similar, come with no test condition, no moisture content and often no engine size. Two independently measured figures are worth more than all of them.

IITA's trainer's manual records a 4.0 horsepower diesel sheller shelling at least 690 kilograms in one hour on 0.3 litres of diesel, against 68.5 kilograms in one hour by one person shelling by hand. That is a work rate ten times faster. Separately, a field trial in the northern Tanzanian highlands that used a motorised sheller to prepare its storage samples reported the machine's throughput as 0.7 tonnes per hour, which lands on the same number from a different measurement. Both figures are Tanzanian, and both are for the small engine class that East African smallholders actually meet.

What a tonne of maize costs you in time, by method. A tonne is roughly eight of the sacks a Ugandan trader actually fills.
Hand shelling, one person. At 68.5 kilograms an hour, a tonne takes about 15 person hours. Two long days for one person, or two people for one day. This is the job most often given to women and children in the study areas.
Stick beating. Faster than hand shelling per hour, which is exactly why Ugandan farmers switch to it for bigger lots, and the reason the grain arrives broken. The speed is bought with breakage.
Four horsepower motorised sheller. At 690 kilograms an hour, a tonne takes under an hour and a half, on about half a litre of diesel, with one person feeding it. Shelling, winnowing and cleaning all happen in that pass.
Sixteen to twenty horsepower sheller. Faster again, usually tractor coupled or on a bigger engine, and built for a trader or a group rather than a farm. The risk moves from throughput to keeping it fed.

Notice what the comparison is not. It is not a cost comparison, because no Ugandan wage rate for casual shelling labour is published anywhere reliable. It is a time comparison, and time in the week after harvest is the scarcest thing a maize household has.

Cracked Kernels and Broken Grain: the Quality That Sets Your Maize Grade

This is the part the machinery pages leave out entirely, and it is where the money is.

A buyer grading maize is looking at moisture first and damaged grain second. Broken kernels matter for a reason that is physical rather than cosmetic: the seed coat is the grain's only defence, and a cracked kernel is an open door. The FAO, WFP and IFAD Uganda study puts it directly, recording that broken grain is more susceptible to mould and weevil contamination and will deteriorate faster during storage. So breakage at shelling is not a one time loss of a few kilograms. It is a slow leak that runs for as long as you hold the crop.

The measured difference is large. IITA's trial work found mechanical shelling cut broken grain by 81 percent and impurities by 38 percent against manual methods, which the manual totals as about a 55 percent gain in quality. Shelling efficiency, meaning grain actually removed from the cob, came in at 98 percent. Grain that would otherwise have been lost to inefficient manual shelling, cleaning and winnowing fell from 68 kilograms per tonne to under 20, leaving about 48 extra kilograms of usable grain in every tonne handled.

Method Grain quality effect Loss per tonne
Hand and stick High breakage About 68 kg
Motorised sheller 81 pc less broken Under 20 kg
Wet shelling Heavy damage Not quantified

Two cautions before you treat that as a promise. The figures are Tanzanian, from Africa RISING trial sites, and a badly adjusted machine run too fast will break grain of its own accord: farmers in the same research programme said plainly that they feared mechanised shelling would cause breakage, and on the larger tractor driven machines they were partly right. Second, it is worth knowing what the grading sheet actually says about breakage. The East African Community maize grading standard caps broken kernels at 2.0 percent for Grade 1, 4.0 percent for Grade 2 and 6.0 percent for Grade 3, alongside a single moisture ceiling that applies to every grade and total aflatoxin at 10 parts per billion with aflatoxin B1 at 5. That moisture figure is itself published at two values, 13.0 percent in one edition of the standard and 13.5 in another, so dry to 13.0 and you clear both. So two kilograms of cracked grain in a hundred is the whole allowance at the top grade, and a stick can put you past it in an afternoon. The separate tolerance for total defective grain is rendered differently by different published versions of the same standard, running from 4, 5 and 7 percent by grade in one to bands reaching 8.5 kilograms per 100 in another, so ask your buyer for their own grading sheet on that one.

The Moisture Window for Shelling Maize

Shelling has a window, and both edges of it cost you money.

Shell too wet and the job is incomplete, the machine works harder, and the grain is badly damaged. IITA's manual states that maize threshed before it is dry enough will most probably be incompletely threshed and will need more energy. The gender study of Tanzanian maize shelling recorded farmers in the lean season reaping immature or insufficiently dried maize and shelling it by hand, and noted that shelling moist maize results in high levels of grain damage. Published work on mechanically threshed maize seed tested five moisture levels from 12 to 24 percent and found damage rising as moisture rose, with the recommendation that a dent type be threshed below 15 percent and a flint type below 18 percent to hold seed quality. That study is about seed rather than grain for sale, which is a real limit on how far it travels, but the direction of the effect is not in dispute.

Shell too dry and you lose in two other ways. The manual is blunt about it: grain that is too dry becomes brittle and will crack during threshing, and too dry grain also means unnecessary weight loss, which is lost money at the point of sale. You are paid by the kilogram, and water that did not need to leave the grain was weight you owned.

What the grain is doing at each stage, and what it does to your shelling decision.
About 30 percent, straight off the plant. Maize in humid and sub humid tropical conditions comes off at around this level. Nothing should be shelled here. The crop is not ready for a machine and it is not ready for a bag.
Around 18 to 20 percent. Grain is still soft enough to bruise and squash rather than release cleanly. A stick at this stage breaks a lot of kernels. A machine at this stage leaves grain on the cob and mashes what it does remove.
Thirteen percent, the target. The ceiling for all three grades under the East African Standard for maize grains. Grain is hard, releases cleanly, and is ready for a sealed bag without needing to come back out and be redried.
Below the target. No published source gives a floor in percent, so the rule is behavioural rather than numeric: dry to the target and shell there. Grain dried well past it is brittle, cracks under the drum, and weighs less than it should when the scale comes out.

The number behind the number is 14 percent. Storage fungi grow on maize held above 14 percent moisture, and Aspergillus flavus, the main toxin producer in stored East African maize, needs about that level plus temperatures around 28 to 30 degrees to make aflatoxin. Drying to 13 rather than 14 is not pedantry. It is the margin that stops an ordinary humid week in a store from putting your grain into fungal territory.

Drying on the Cob Before Shelling, Not After

The sequence matters as much as the machine, and IITA's own operating instructions start with it: husk and dry the maize so the grains are loosened on the cob, and shelling then needs the minimum energy input. A dry cob gives up its grain almost willingly. A wet one has to be forced.

There is a piece of engineering history that makes the point harder than any recommendation could. When FAO trialled mobile maize drying equipment in a maize growing region with a wet harvest season, a small mobile batch dryer for already shelled maize worked and was economic, but it was superseded by drying the cobs in the farmer's own crib instead, and the report gives as one reason that in crib drying eliminated the problems associated with shelling high moisture cob maize. In other words the best solution to wet shelling was not a better sheller or a dryer for the grain. It was drying the cob before the sheller ever saw it.

For a Ugandan smallholder that translates into something buildable: a raised crib or a clean sheet, cobs dehusked and spread thinly, turned, and brought under cover at night. IITA's trial data supports the detail as well, since drying cobs with their husks still on raised insect infestation by factors of 1.8 and 2.2 at its two sites. Dehusk, then dry, then shell. The maize drying guide covers the method and grain moisture management covers how to know when you have arrived.

Maize Sheller Sizes From Four to Twenty Horsepower

Research on farmers' willingness to invest in mechanised maize shelling in Tanzania costed four engine sizes actually available in the market: 4, 7, 16 and 20 horsepower. The four horsepower diesel machine was the one identified as preferred by the majority of smallholders in the separate IITA review of shelling efficiency, grain output and farmer capacity. Smaller is not a compromise here. It is usually the right answer, and the reason sits in the next section.

Power source is the other axis. Shellers are built around hand cranks, petrol engines, diesel engines, electric motors and tractor power take off. In rural Uganda a diesel engine removes the grid from the problem, which is why the machines that circulate in villages tend to be engine driven rather than electric. Electric is cheaper to run where three phase power actually reaches, and that is a town or a trading centre rather than a garden.

Keeping a Sheller Busy Across the Maize Harvest

Here is the thing nobody selling a sheller will tell you: the machine's problem is not throughput, it is idleness.

The Tanzanian investment study modelled full capacity on the assumption that the shelling season lasts about a month after harvest, with a two day break each week, running five to eight hours a day. That is a short earning window for an asset you keep all year. Working inside it, the study found the 7 horsepower machine needs about 38 tonnes of maize shelled in a year to break even, the 16 horsepower about 60 tonnes, and the 20 horsepower about 75 tonnes. The 4 horsepower machine is not profitable at all below roughly half its capacity use.

Then the conclusion that inverts the usual buying instinct. The study found the 4 horsepower machine most likely to be fully used and the 20 horsepower most likely to be underused, because the bigger the machine, the harder its owner has to work to pull in enough clients to feed it. Buying capacity you cannot fill is the commonest way this investment fails.

Work out your own catchment before your own throughput. How many acres of maize sit within pushing distance in the month after harvest, how much of it is already served, and how many of those households will pay rather than pick up a stick. If you want to run the arithmetic properly, the break even calculation takes tonnes and costs and gives you the volume you need, and how a farm machinery hire business actually works covers the service side in more detail than belongs here.

Reaching a Sheller in Uganda: Hire, Group or Own

Three routes, and the research is clear about which one most farmers want.

Asked in Tanzania's Babati and Kongwa districts, 80 percent of farmers said they would take up mechanised shelling if it were available as a rental service. Sixty two percent would take it up by pooling resources in a producer group. Only 30 percent would buy as individuals. The gap between those numbers is price, and the rental model wins precisely because it does not ask a smallholder to own an asset that earns for one month a year. The same body of work found service prices differed by who was providing them, with individual entrepreneurs charging roughly a third more than farmers' groups for the same bag.

That points at something practical for a Ugandan village. If shelling is done on hire in your area, a group that buys jointly and serves its own members is competing against a price you already know, and the margin it captures stays in the village. If no machine comes at all, which the Uganda study found was the case for most of the farmers it interviewed, then the first question is not which machine but whether anyone within reach owns one you can pay.

One warning from the literature that has nothing to do with engineering. A documented case elsewhere in Africa saw a women's cooperative forced to sell its project funded sheller and return to manual processing after men in the community opposed the initiative and seized the machine. Where a group buys a machine, who controls it, who books it and who keeps the takings needs writing down before the machine arrives, not after.

Running a Sheller Without Losing Grain on the Farm

A well run machine and a badly run machine of the same model give different grain. The operating sequence from IITA's manual is worth following in order.

Getting a hired or owned sheller through a batch without leaking grain or quality.
One. Husk and dry first. Grain loosened on a dry cob shells with minimum force, which is the single biggest control you have over breakage.
Two. Sort before feeding. Pull out damaged and mouldy cobs and keep them out of the batch. One rotten cob spreads its spore load through everything the drum touches afterwards.
Three. Clean the machine and clear the hopper. Check the hopper and shelling chamber for obstructions. Residue from someone else's lower grade maize is a contamination route, and mills have the same problem for the same reason.
Four. Stand it on a clean sheet. Level ground, tarpaulin spread, grain landing on fabric and not on soil. Drying and shelling on bare ground is the documented route by which Ugandan maize picks up debris and fails the market standard.
Five. Bag the chaff exit. Fasten a collecting bag where the chaff and dust leave. It keeps the yard clean and it lets you see whether the fan is blowing out grain along with the trash.
Six. Watch the first bucket. Look at what comes out before you commit the batch. Cracked and split kernels in the first bucket mean the drum speed is wrong or the grain is at the wrong moisture. Stop and fix it while it is still one bucket.

Keep the cobs. In the Tanzanian work, farmers preferred machines that did not smash the cob because whole cobs are worth having as fuel, and cobs sometimes formed part of what a hired sheller was paid with. A machine that returns the cob intact is giving you a second product. Keeping farm equipment serviced matters more on shared machines than owned ones, because nobody feels responsible for a machine everybody uses.

Shelling, Storage and When You Sell the Maize

Maize is a low value per acre crop with a fairly stable price, so the money in it is not in growing more. It is in not selling in the same week as everyone else. The yield per acre you can reach is bounded, and the harvest price is bounded too, but the gap between the harvest price and the price three or six months later is real and it is yours if you can hold the crop.

Shelling is what makes holding possible. Grain stores far better than cob, it takes far less space, and it is what a sealed bag or a silo is built for. But only if it went into the bag dry and unbroken, which returns you to every paragraph above.

There is a striking piece of evidence for this in FAO's own intervention costing for Ugandan maize loss reduction. The budget it builds for motorised shellers, ten per subcounty against 5,520 tonnes of maize a year, prices the grain saved at UGX 800 per kilogram, and the footnote states outright that this is the price attained if grain is sold after six months' storage. The business case for the machine is written on the assumption that you do not sell at harvest. That is the whole cluster in one line.

What happens next is storage, and it has its own failure modes. Uganda's on farm losses after shelling run at a district mean of 10 percent, and the study found aflatoxin above the 10 parts per billion limit in half the farm samples in Apac and 30 percent in Lira after just three months. Getting the grain into a store that holds is covered in the maize storage guide, sealed bags in hermetic grain storage bags, and the insects in preventing weevils in stored grain. If your plan is to mill rather than sell grain, maize milling machines is a different business with a different constraint.

Questions Ugandan Farmers Ask About Maize Shelling Machines

What does a maize sheller cost, and what does shelling cost as a service? No reliable Ugandan purchase price is published, and dealer listings move with the exchange rate and the bundle, so this page will not print one. For scale, research in Tanzania recorded the market price of the four horsepower diesel machine at about 1.4 million Tanzanian shillings at the time of its survey, and a shelling service charge of about 1,000 Tanzanian shillings per 100 kilogram bag, with individual operators charging roughly a third more than farmers' groups. Treat those as the shape of the numbers and not as Ugandan prices. For a Ugandan figure, ask two or three operators in your subcounty and collect three written quotations on one specification if you are buying. The per acre shelling cost range for Uganda sits on the cost of maize farming per acre page, and current grain prices are on the maize price page.

Is a sheller worth buying for my own maize? Almost certainly not, if you are a smallholder. The break even volumes are the reason: 38 tonnes a year for a seven horsepower machine, 60 for a sixteen and 75 for a twenty, against a shelling season of roughly one month. Few Ugandan farms grow that much. The machine pays as a service to a catchment, which is why 80 percent of surveyed farmers said they would use one on hire and only 30 percent would buy one.

At what moisture content should I shell? At your storage target, which is 13 percent or below under the East African Standard for maize grains. Wetter than that and the shelling is incomplete and the grain bruises. Published threshing work found damage rising steadily across moisture levels from 12 up to 24 percent. Drier than the target and the grain turns brittle and cracks, and you have also thrown away sellable weight. No source gives a lower limit in percent, so the working rule is to dry to the target and shell there.

Does a machine really break less grain than a stick? The measured answer from IITA's Tanzanian trials is yes, and by a wide margin: 81 percent less broken grain and 38 percent fewer impurities, with shelling efficiency at 98 percent. The caveat is that this is a properly set up machine at the right moisture. A machine run too fast on wet cobs will break grain enthusiastically, which is why farmers in the same research were sceptical of mechanised shelling in the first place.

Why does broken grain lower my price? Because the seed coat is the grain's defence and a crack removes it. Ugandan field research states plainly that broken grain is more susceptible to mould and weevil contamination and deteriorates faster in storage, so a buyer taking cracked grain is buying a problem that grows in their own store. Graded lots tighten the tolerance for damaged and defective grain at each step up, though the published renderings of that tolerance disagree with each other, so use your buyer's grading sheet.

Can I shell maize in the field and bag it there? Some farmers do, and the FAO study recorded it. It saves transport of cob weight you do not want. What it risks is shelling before the crop is dry, bagging on soil, and having no cover when rain arrives. If you shell in the field, shell onto a sheet, and only after the cobs are genuinely dry.

How do I stop a hired machine contaminating my grain? Watch it arrive and watch it get cleaned. Residue in the hopper and chamber from a previous, lower grade batch is a documented contamination route in Ugandan maize processing, and so is standing the machine on bare soil. Ask for the chamber to be cleared, spread your own tarpaulin, and keep mouldy cobs out of the feed.

Does shelling remove aflatoxin? No. Nothing you do after the toxin has formed removes it at farm level. Shelling and cleaning take out visibly mouldy kernels and dust, which helps, but the toxin in the remaining grain stays there. Shelling matters because unbroken grain is far less likely to develop the problem in the first place.

Comparing Maize Shelling Machines and Shelling Services in Uganda

Before you spend anything, find out what already circulates near you. Ask at the nearest trading centre whether a sheller comes through after harvest, what it charges per bag, and whether it is owned by an individual or a group, because that difference showed up as roughly a third on the price in the East African research. If you are considering buying, get three written quotations on one specification, and make each one state the engine size, the claimed output with the moisture content it was measured at, what spares are held locally and who services the machine. A throughput figure with no moisture content attached is not a specification. Check the current grain price before you commit, since the value of the grain a machine saves you is the only thing that makes it worth paying for, and look at what else in the farm machinery guides your farm needs first: a weighing scale costs a fraction of a sheller and often settles a bigger argument about money.

More in Farm Machinery