414 guides across 21 subjects
Every figure traced to a named source
Prices in Ugandan shillings, per acre and per animal

How to Calculate Irrigation Water Requirements

Drip irrigation tape running along a crop row

Irrigation planning fails in two places: not knowing how much water the crop needs, and not checking whether the source can deliver it in the hours available. The second is the one that strands a pump and a tank on a plot that cannot be watered.

Millimetres, and what they are worth in litres

Crop water demand is expressed in millimetres per day, the same unit as rainfall. One millimetre means one litre spread over one square metre.

1 mm over 1 hectare = 10,000 litres, or 10 cubic metres.

1 mm over 1 acre = about 4,047 litres, or roughly 4 cubic metres.

So a crop using 5 mm a day on one acre needs about 20,000 litres a day. Over a dry week with no rain, that is 140,000 litres, which is a number worth knowing before buying a tank.

Working out the demand

Crop water requirement is reference evapotranspiration multiplied by a crop coefficient.

Crop water need (mm/day) = ETo multiplied by Kc.

ETo is how fast a short green reference crop loses water under your local conditions, and it changes with sunshine, temperature, humidity and wind. It is not a constant you can carry between districts or between months, and it is highest exactly when you most need the answer.

Kc is a factor for the crop and its growth stage, low just after planting when the ground is mostly bare, highest at full canopy and flowering, falling again as the crop matures.

Get ETo from a local source rather than a remembered figure: the nearest meteorological station, an extension officer, or a simple evaporation pan on the plot read daily. A pan reading is crude but it is yours, it responds to this week's weather, and it beats a national average by a wide margin.

Net demand, after rain

Irrigation only has to supply what the rain does not. Subtract effective rainfall, which is the part that actually enters the root zone rather than the part that ran off a hard surface or fell after the soil was already full.

Irrigation need = crop water need minus effective rainfall.

A rain gauge on the plot costs very little and removes the guesswork. Irrigating to a schedule through a wet fortnight wastes fuel, leaches fertiliser below the roots and on heavy ground does real damage.

Then allow for the losses of your system

Not all the water you pump reaches a root. How much is lost depends on the method, and this is where the two main systems genuinely differ: a furrow loses to deep percolation and runoff, a sprinkler loses to wind and evaporation in the air, and drip loses least because it puts water at the plant rather than over the whole surface.

Water to pump = irrigation need divided by the system efficiency.

At an efficiency of 0.6, a crop needing 20,000 litres requires about 33,000 litres pumped. At 0.9 it requires about 22,000. Over a season that difference decides whether a borehole is adequate. How the systems compare in practice is in sprinkler irrigation explained and greenhouse irrigation systems.

Can the source deliver it in the hours you have?

This is the check that gets skipped. A daily requirement is meaningless unless the source can supply it in the time available.

Required flow (litres per hour) = daily volume divided by the hours you can irrigate.

33,000 litres over six hours needs about 5,500 litres an hour, which is roughly 92 litres a minute, sustained. Measure what your source actually gives by timing how long it takes to fill a drum of known volume, and do it at the end of the dry season rather than after rain. A borehole or stream that falls away in February is the binding constraint on the whole plan: see boreholes for agricultural irrigation.

Storage

A tank buys you the difference between a slow source and a fast application. Size it against the daily requirement and the hours the source runs, not against a round number. If the demand is 33,000 litres a day and the source yields steadily for twelve hours, a tank holding roughly a day's demand lets you irrigate on your schedule instead of the borehole's.

Frequently Asked Questions

How many litres is one millimetre of irrigation? One litre per square metre. That is 10,000 litres over a hectare and about 4,047 litres over an acre. Working in millimetres keeps irrigation and rainfall in the same unit, so you can subtract one from the other directly.

What is ETo and where do I get it for my area? ETo is reference evapotranspiration, the rate a short green reference crop loses water under local weather. It changes with district and month, so a single figure is not safe to reuse. Take it from the nearest meteorological station or extension office, or read an evaporation pan on the plot daily, which is crude but local and current.

Do I still irrigate when it rains? Only for the shortfall. Subtract the rain that actually reached the root zone from the crop's requirement and supply the difference. Irrigating on a fixed schedule through a wet spell wastes fuel, pushes fertiliser below the roots and can waterlog heavy soils.

Why do I need more water than the crop needs? Because no system delivers everything it pumps to a root. Furrow irrigation loses to runoff and deep percolation, sprinklers lose to wind and evaporation, drip loses least. Divide the crop's requirement by your system's efficiency to get the volume to pump.

How do I know if my borehole can keep up? Measure the flow rather than trusting the rating. Time how long it takes to fill a container of known volume, and do it late in the dry season when the yield is at its lowest. Then compare that rate against the litres per hour your plan requires in the hours you can actually irrigate.

More in Farm Calculators and Record Templates